![]() ![]() It’s pretty easy to tell if you have more strands on one side of the peep than the other. If you bought a used bow and no peep is inserted, or you removed your peep for some reason and have no idea where half-and-half would be, press the bow, guesstimate, insert the peep and look. This string separates the strands in half, so half of the string sits on one side of the peep notch and the other on the other half. You may find your ideal height is more or less, but this range is a good starting point. If your bowstring is brand new, the string manufacturer will place a piece of serving string through the middle of the bowstring, and it’s there for a reason. Typical peep sight height is usually between 5-1/2- and 7 inches above the center of the D-loop. Now it’s time to install your peep sight. Once your peep sight is installed, draw your bow outside and make sure the peep is perfectly aligned with the sight housing. Some rests, like those from QAD, have timing marks to help guide you in this case you need a friend to watch the timing marks as you draw. As you draw, the rest’s arm should reach its vertical position about the same time your bow’s cams roll over to let off. You can use a draw board if you have one, or you can simply draw the bow with a release set not to fire and watch as the rest’s arms come up. Timing a rest is not difficult, but it’s a key step in how to set up a compound bow. If you are using a drop-away rest, you now need to attach the rest’s cable to one of the bow’s limbs or to the down cable, depending on the model of rest you use. The author pulls the cord of a drop-away rest through a bow’s down cable. Just level your bow in a bow vise, follow the rest manufacturer’s instructions to install it to the riser, and eyeball it level. The good news is that all of them are very simple to attach. ![]() Many models still connect to the riser via the bow’s Berger hole(s), but some models, like many from QAD and others that have adapted QAD’s Integrate Mounting System, mount to a pair of dovetail slits recessed into the back face of the bow’s riser. The first step for how to set up a compound bow, arrow-rest mounting has changed significantly over the last three years. This QAD arrow rest is attached to the Berger hole, but other models can be installed via a dovetail mount. A day of humid weather or serious temperature change will cause the peep to rotate enough to block your vision completely.How to Set Up a Compound Bow, Step-By-Step Step 1: Attached the arrow rest. My point is this: If you’re barely able to see through your peep while shooting at home because of peep rotation, you’re going to get yourself into trouble when you take the bow afield. To be completely safe, I expose my bow to a little heat and a little cold, as well as some serious humidity, before I go hunting. Hot and cold weather, as well as high humidity, can cause the string to twist. However, when you take a bow into the elements (e.g., when you take it on a hunting trip), all change will be accelerated, especially peep rotation. In my experience, bows that are kept inside the house and only taken outside to shoot in the backyard don’t tend to change very quickly. Shooting isn’t the only thing that causes the string to twist and the peep to rotate. By separating the colors, you essentially split the string perfectly in two, so it’s not as likely to turn during the draw cycle. Today’s custom strings also make installing your peep in the exact center of the string easy because many of them are made of two different colors of fiber. (The direction the string begins to rotate is the direction it will continue to rotate if left to itself.) ![]() Unfortunately, as you continued to shoot the bow, the string settled in and rotated a little clockwise or counterclockwise. When you installed your peep sight, you presumably adjusted it to come back in perfect alignment. (You can incrementally rotate the peep by using this method, but not once it is fully tied in.) Aftermarket Answer This ensures that you have the same number of fibers on each side of the peep. You then take a single fiber from the opposite side of the peep and take it around the peep in the same direction. This is a time-intensive operation, as it requires a great deal of trial and error to get it just right.Ī faster and more consistent way is to press the bow, then take a single fiber from one side of the string (where it splits to go around the peep) and move it around the peep to the other side. You need to shoot a couple of shots each time you tinker with the peep to let things settle into their new positions. You can do this from either the top or bottom cam, but the peep will rotate a bit less with a twist from the bottom because the peep is closer to the top cam. A tried-and-true method is to press the bow and add or remove string twist. There are a couple of ways to correct this problem when you get home, too. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |